搜索资源列表
8×8dotmatrix
- 利用595实现串口数据传输,控制led点阵8×8的显示- Using 595 realizations strings mouth data transmission, controls the led lattice 8脳8 demonstration
LEDDENG
- LED灯,1片89C51两片595+4片LED灯程序-LED lights, a two 89C51 595 four LED lights procedures
LED
- atmega16+595+154做的16*16单色点阵-the ATmega16+595+154 do 16* 16 monochrome dot-matrix
595-3
- 74hc595串行数据输入 并行输出 控制3-stri led流水-A 74hc595 serial data input parallel output control 3-stri led water
led
- 是用51单片机为主控芯片,然后使用154和595进行辅助控制-51 microcontroller as the master chip, and then display Chinese characters dot matrix module
stm8s---595
- stm8s103k驱动9个hc595 控制72个贴片led-9 stm8s103k drive the hc595 control 72 SMD led
595-165
- 使用74HC595和74HC165实现八个按键输入,四位LED数码管显示,并有外部调用函数。-Use 74HC595 and 74HC165 achieve the eight keys to enter the four-digit LED digital tube display, and call functions outside.
164-595-2
- 单片机LED点阵164-595-2仿真原理图,程序等-Microcontroller LED dot matrix the 164-595-2 simulation schematic procedures
LED
- 多位7段数码管动态显示程序(PIO+595)完美运行-failed to translate
74LS595--for--LED-SCREEN
- 74LS595在LED screen上的应用很多,主要用于级联显示数据。本例演示了595的基本应用,方便移植使用。-74LS595 application on the LED screen a lot, mainly for cascading display data. This example demonstrates the basic application 595 to facilitate the use of transplantation.
LED
- stm32 模拟电梯的led程序,使用数码管 595 和步进电机-stm32 simulated elevator led program that uses digital tube 595 and stepper motors
proteus-595
- 6个595级联,输出48个LED闪烁灯,附有proteus仿真图。-6 595 cascaded output 48 LED flashing lights, with proteus simulation map.
32-buttons-1--595
- 32按键控制32个LED灯并带一个74HC595扩展。每一个按键独立控制一个LED亮灭,并且,通过了proteus 仿真。-32 buttons control the 32 leds with a 74 hc595 are needed. Each key independent control destroy an LED light, and, through the proteus simulation.
run-LED
- 旋转LED平面字体测试程序 用单片机的串行口发送数据给3个595 并行驱动LED 采用无线供电方式以及性能较好的RF370电机,在5V供电下 显示的效果非常好.电机速度也够快 够安静. 只为简单的理解显示的原理,利用人眼视觉暂存,用电机旋转做列扫描, 每送一列数据延时 再送下一列数据,原理比较简单,跟点阵显示差不多。-Rotating LED flat font test program with single-chip microcomputer serial port to s
4key
- 自己整理的关于595驱动4位数码管的51单片机程序-51MCU C program for drive LED(595)
8-led-dxp
- 8位数码管显示,采用595级联的方式,具有多种移动的选择,能够时时刷新,利用红外的传感器。-8 digital tube display, using 595 cascaded manner, with a variety of mobile choice, can always refresh, using infrared sensor.
LED-DISPLAY
- LED点阵 显示汉字,16*16LED矩阵,16位和后16位数据正好是相反的,也就是说先让第3个595输出低电平,然后再让第4个595输出低电平,从而实现显示汉字。
595
- 驱动LED灯带 采用74HC595移位寄存器 CPU是STM32-DRIVER FOR LED TAPE.74HC595 IS THE CONTROL TEBLET.THE CPU IS STM32
595(SPI)
- 使用SPI协议来驱动595芯片,来对8盏LED灯进行控制,程序简单易懂-Use SPI protocol to drive 595 chips, to control 8 LED lights, the program is simple and easy to understand
4位时间数码管模块 LED显示 四位串行 595驱动
- 4位时间数码管模块 LED显示 四位串行 595驱动(4 bit time digital tube module LED displays four bit serial 595 driver)